New Turbine Control System (DCS) at Skærbækværket Power Plant Unit 3

DONG Energy Power A/S

This contract notice concerns renewal of CPU-based turbine control and turbine protection system for Power plant Skaerbaek Power Plant Unit 3, 410 MW steam turbine supplied by Alstom commissioned in November 1997. Turbine include cylinders for double reheat, LP-bypass and district heat control. DONG Energy Power A/S foresee new CPU’s include functionalities for all turbine control and protection.

Deadline

Fristen for modtagelse af bud var på 2012-02-28. Indkøbet blev offentliggjort på 2012-01-25.

Hvem?

• DONG Energy Power A/S

Hvad?

Hvor?

• Midtjylland › Østjylland

Indkøbshistorik

Dato	Dokument
2012-01-25	Udbudsbekendtgørelse

Udbudsbekendtgørelse (2012-01-25)
Objekt
Omfanget af udbuddet
Titel: Overvågnings- og styresystem
Mængde eller omfang:

The Skaerbaek Power Plant Unit 3 (SKV3) is equipped with doublet reheat steam system and the turbine has following data:— Manufacturer ALSTOM,— Back pressure turbine,— Load electric between 75 MW and 445 MW. Nominal 410 MW,— Nominal steam flow 265 kg/s,— VHP steam pressure 288 bar, temperature 580 °C,— HP steam pressure 84 bar, temperature 580 °C,— IP0 steam pressure 22,5 bar, temperature 580 °C,— District heating 0-450 MJ/s, temperature 90-120 °C.The present control and protection system TCS/TPS shall be exchanged to a new modern TCS/TPS system suitable for turbine units.Controls:— Speed run-up control,— Speed – droop control (valve position). Speed control without load,— 1. Wheel pressure control (Load control with gradient control and speed-droop),— Boiler pressure control,— Rotor Stress evaluation,— Frequency support,— Speed and load gradient limitation by thermal stress,— Test of overspeed,— VHP, HP and IP0 backpressure control,— VHP and HP switch and isolation,— IP1 and IP2 back pressure limitation,— Temperature control for District Heating,— LP-bypass pressure control and water injection.Protections:— Over-speed,— Rotor Stress,— Steam pressure limits,— Tightness test of safety valves and control valves,— Individual test of the trip coils.Electrical output and controlling of all valves and flaps on turbine and LP-bypass.The scope comprises functions programming in TCS/TPS for all controls, limitations and protection functions on the turbine.The scope for TCS/TPS system comprises design, engineering, Hardware, production, FAT test, installation, commissioning of the TCS/TPS and 720 h trial run.

Bekendtgørelsens metadata
Originalsprog: engelsk 🗣️
Dokumenttype: Udbudsbekendtgørelse
Kontraktens art: Varer
Forordning: Den Europæiske Union, med deltagelse af GPA-lande
Fælles glossar for offentlige kontrakter (CPV)
Kode: Overvågnings- og styresystem 📦

Procedure
Procedureform: Udbud efter forhandling
Bud-type: Indsendelse gældende for alle delaftaler
Kriterier for tildeling
Det økonomisk mest fordelagtige bud

Ordregivende myndighed
Identitet
Land: Danmark 🇩🇰
Type af ordregivende myndighed: Forsyningsvirksomhed
Navn på ordregivende myndighed: DONG Energy Power A/S
Postadresse: Klippehagevej 22
Postnummer: 7000
Postby: Fredericia
Kontakt
Internetadresse: http://www.dongenergy.dk 🌏
E-mail: olelh@dongenergy.dk 📧
Telefon: +45 99552840 📞

Reference
Datoer
Afsendelsesdato: 2012-01-25 📅
Tilbudsfrist: 2012-02-28 📅
Offentliggørelsesdato: 2012-01-28 📅
Identifikatorer
Bekendtgørelsesnummer: 2012/S 19-031145
EUT-S-nummer: 19
Yderligere oplysninger

This notice is a call for prequalification. In order to be prequalified, it is important that all information requested under III.2) Conditions for participation, is included in the request. The request to participate in the prequalification shall be submitted by E-mail to the contact point mentioned in I.1). Further specifications or additional documents to this contract notice are not available at the contact point given in I.1). When the prequalification procedure is finalized, a maximum of five (5) prequalified companies will be invited to submit a tender.

Objekt
Omfanget af udbuddet
Kort beskrivelse:

Mængde eller omfang:

The Skaerbaek Power Plant Unit 3 (SKV3) is equipped with doublet reheat steam system and the turbine has following data:

— Manufacturer ALSTOM,

— Back pressure turbine,

— Load electric between 75 MW and 445 MW. Nominal 410 MW,

— Nominal steam flow 265 kg/s,

— VHP steam pressure 288 bar, temperature 580 °C,

— HP steam pressure 84 bar, temperature 580 °C,

— IP0 steam pressure 22,5 bar, temperature 580 °C,

— District heating 0-450 MJ/s, temperature 90-120 °C.

The present control and protection system TCS/TPS shall be exchanged to a new modern TCS/TPS system suitable for turbine units.

Controls:

— Speed run-up control,

— Speed – droop control (valve position). Speed control without load,

— 1. Wheel pressure control (Load control with gradient control and speed-droop),

— Boiler pressure control,

— Rotor Stress evaluation,

— Frequency support,

— Speed and load gradient limitation by thermal stress,

— Test of overspeed,

— VHP, HP and IP0 backpressure control,

— VHP and HP switch and isolation,

— IP1 and IP2 back pressure limitation,

— Temperature control for District Heating,

— LP-bypass pressure control and water injection.

Protections:

— Over-speed,

— Rotor Stress,

— Steam pressure limits,

— Tightness test of safety valves and control valves,

— Individual test of the trip coils.

Electrical output and controlling of all valves and flaps on turbine and LP-bypass.

The scope comprises functions programming in TCS/TPS for all controls, limitations and protection functions on the turbine.

The scope for TCS/TPS system comprises design, engineering, Hardware, production, FAT test, installation, commissioning of the TCS/TPS and 720 h trial run.

Sted for udførelsen
Hovedsted eller sted for udførelsen:

DONG Energy Power A/S.

Skærbækværket.

Klippehagevej 22.

DK-7000 Fredericia.

Juridiske, økonomiske, finansielle og tekniske oplysninger
Betingelser for deltagelse
Egnethed til at udøve det erhverv:

A1. A solemn declaration as to whether the tenderer has fulfilled his obligations in respect of the payment of contributions to social security schemes in accordance with the legislation in the country in which the tenderer is domiciled and in Denmark. And to whether the tenderer, has fulfilled his obligations in respect of the payment of taxes and duties in accordance with Danish legislation.

A2. Tenderers domiciled in Denmark must enclose documentation in the form of a Service Certificate, no more than 6 months old, issued by the Danish Commerce and Companies Agency. Tenderers domiciled in countries other than Denmark must obtain the required documentation in another way from the relevant authorities in the country concerned.

Økonomisk og finansiel stilling:

B1. Ownership and corporate form. If the applicant is a subsidiary, the name and address of the parent company must be stated as well as any information on the name and address of a Danish representative.

B2. Name and address of the applicant’s bank.

B3. Annual accounts for the previous three years and if 50 % (or more) of the company is owned by another company, the same information is desired concerning the parent company. The accounting information shall include net turnover, result of primary operations, result after taxation, balance sheet total, equity ratio (equity capital as percentage of the total assets).

B4. Documentation that the applicant can, in case of contract, provide a bank guarantee or guarantee commitment of 10 % of the contract value as security for meeting his obligation to deliver.

Teknisk og faglig kompetence:

C1. Documentation of the applicants quality management system is required. If the applicant is eg. ISO 9001 certified a copy of the certificate can be used as documentation. If a non-certified system is utilized it is required that the applicant describes:

a) the executive policy of the company concerning quality management - including name and position of the person who is responsible for the quality management in the company,

b) the system for document control in the company,

c) how the company assures that systems, procedures and/or working procedures are monitored,

d) how the company works to prevent and correct actions to diminish deviations from systems, procedures and/or working procedures,

e) how the company evaluates its quality management system,

f) the company's program for instructing employees in quality management and initiatives to secure the employees ability to carry out the job,

g) how the administration of sub-supplier is conducted.

h) procedures for quality control of works performed in the shop, and procedures for documentation of fact finding and reporting in general.

C2. Documentation of the applicants health and safety management system is required. If the applicant is eg. OHSAS 18001 certified a copy of the certificate can be used as documentation. If a non-certified system is utilized it is required that the applicant describes:

a) the executive policy of the company concerning health and safety management - including name and position of the person who is responsible for the health and safety management in the company,

b) how the company assures that systems, procedures and/or working procedures to follow up on unwanted incidents are monitored,

c) how the company evaluates its health and safety management system,

d) how the company works to improve the working environment,

e) how the company has learned from cases where injunctions has been written out or fines has been received for breaking the health and safety legislation,

f) how the applicant assures that sub-suppliers comply with the health and safety legislation etc.

C3. Documentation of the applicants environmental management system is required. If the applicant is ISO 14001 certified a copy of the certificate can be used as documentation. If a non-certified system is utilized it is required that the applicant:

a) describes the executive policy of the company concerning environmental management - including name and position of the person who is responsible for the environmental management in the company,

c) how the company evaluates its environmental management system,

d) how the company works to reduce its impacts on the environment,

e) how the company has learned from cases where injunctions has been written out or fines has been received for offence of the environmental legislation.

C4. Organisation chart of the applicant.

C5. Statement of the applicant’s facilities for detailed engineering, planning and management of the works.

C6. Statement of the applicant’s workshop and production facilities.

C7. References of similar renewal of TCS/TPS system supplies to turbine sets, which the applicant has on order or has delivered within the last 5 years in Europe. The list of references shall include information for contact to owners of referred systems (name, address, telephone number etc.) and extent of work (disciplines involved, duration, place and value of contract).

Kontraktens udførelse
Krav om deponering og sikkerhedsstillelse: The terms will be stated in the tender invitation documents.
De vigtigste finansieringsbetingelser og betalingsordninger og/eller henvisning til de relevante bestemmelser, der regulerer dem: The terms will be stated in the tender invitation documents.
Den juridiske form, som den sammenslutning af økonomiske aktører, der skal have kontrakten, skal have: The terms will be stated in the tender invitation documents.

Procedure
Sprog
Sprog: dansk 🗣️
engelsk 🗣️

Ordregivende myndighed
Kontakt
Enhed: Ole Lund Hansen
Internetadresse: www.dongenergy.dk 🌏
E-mail: kfst@kfst.dk 📧

Reference
Datoer
Startdato: 2012-09-02 📅
Slutdato: 2013-11-29 📅

Supplerende oplysninger
Gennemgå organ
Navn: Klagenævnet for Udbud
Postadresse: Erhvervs- og Selskabsstyrelsen Kampmannsgade 1
Postby: København V
Postnummer: 1780
Land: Danmark 🇩🇰
Telefon: +45 33307621 📞
Internetadresse: www.klfu.dk 🌏
Fax: +45 33307799 📠
Navn: There are non in Denmark
Oplysninger om frister for klageprocedurer:

The deadlines are provided in Danish act no. 492 of 12.5.2010 on enforcement of the public procurement rules, etc (only available in Danish).

Complaints about not having been prequalified must be filed within 30 calendar days from the day after the day when the contracting entity has notified the applicants in question about the result of the prequalification provided that the notification contains a short statement of relevant reasoning behind the decision.

The complainant must notify the contracting entity in writing of the filing of a complaint with Klagenævnet for Udbud (the Review Board for public procurement) at the latest when he files the complaint with Klagenævnet for Udbud, and the notification must contain information about whether the complaint is filed in the standstill period.

If the complaint is not filed in the standstill period, the complainant must also state if it is requested that the complaint be granted suspensory effect.

Tjeneste, hvorfra der kan indhentes oplysninger om klageproceduren
Navn: Konkurrence- og Forbrugerstyrelsen, Center for Jura og Udbud
Postadresse: Nyropsgade 30
Telefon: +45 72268000 📞
Internetadresse: www.kfst.dk 🌏
Fax: +45 33326144 📠
Kilde: OJS 2012/S 019-031145 (2012-01-25)

Nye indkøb inden for beslægtede kategorier 🆕

Industrimaskiner (4 nye indkøb)

Diverse maskiner til generelle og specielle formål (2)

Overvågnings- og styresystem, tryk- og grafikudstyr, kontorautomatiseringudstyr og informationsbehandlingsudstyr (1)

Overvågnings- og styresystem